Automatic SWR Circuit (no complicated calibration
procedure)
"Talkback" Circuit with On/Off Switch and
Volume Control
Variable Power Output Control
Roger Beep with On/Off switch and LED Indicator
Galaxy Noise Filter for use on weak signals
High SWR Alert LED Indicator
Two Year Warranty as explained below:
Five-digit Frequency Display
+/- 1.0 kHz Receive Clarifier
Noise Blanker and Automatic Noise Limiter
AM, SSB and PA Modes
3-Position Tone Control Switch
Green/Red LED Indicator for RX/TX
LED Channel Indicator
Dimmer Control
Receive Gain Control
Mic Gain Control
Tune-up Reports
and Custom work done here at BellsCB:
This is a playlist and has multiple videos
(notice
the
button to change to the next video)
As many of you may know; Ranger, Galaxy and General
radios have all had some poor tolerance coax connectors this
last year (SO-239 on the back of the radio) . You have to
wiggle the coax just right to get a good grab on the threads
of the connector. They are too far “out of tolerance” and we
can no longer accept it. So we have started changing
the coax connectors ourselves to a much higher quality
SO-239 that will fit your coax nice and tight. This has
affected our selling price ($10) but we think you will agree
that it is worth it.
Galaxy radios sometimes have a small scratch or
ding that the factory covers with black touch up. We cannot
effect this and do not guarantee your radio to be cosmetically
perfect. Bells CB will make no marks or scratches on your radio
ourselves. Galaxy might though and I cannot control it.
Tune-up. 25+ W
peak power (perform a tune-up and
a;lignment to the radio
to increase power, audio and RX performance)
$39
RFX-95
Final.
Install a completely new final
section consisting of a high power MOSFET and perform a
tune-up to the entire radio to increase power, audio and performance
with an AM carrier
of 20 watts with 90+ watts peak power.
$189
Change
factory power cord
to a 10 Gauge
Power Cord (14 foot) and modify the DC Jack for high
amperage 2 Pin Quick connector. This is only helpful when
you have the RFX-95HD2 and is NOT required for a stock radio
$59
Perform
Receiver improvement mods. (These mods
replace key RX parts for better sensitivity and selectivity)
$26
Install
an
CP-1 Top Gun Audio Compressor.
(on - all the time) This amplifies your lower level audio on transmit. NOTE: It becomes difficult to use the Talkback even at low volume with this mod.
$25
Tune-up
and frequency conversion. (Install
extra channels with switches in back of radio and
tune up radios output)
$79
Clarifier "Slider" conversion.
(Modify the Clarifier to control TX and RX frequency. This mod is an add-on to the
two frequency conversion mods
listed above and if done separately will cost $35)
$35 /
$15
Turner
RK-56
Noise Canceling microphone.
(wired for this radio with
a 4 pin plug)
$46
Astatic
636L Noise
Canceling microphone.
(wired for this radio with
a 4 pin plug)
$29
Astatic
RD104-E Amplified microphone.
(wired for this radio
with a 4 pin plug and
a battery installed)
$46
Install an Echo Board
(Side)
(wired internal to the radio with
dual controls on the left side to control speed and echo
effects)
$65 or $75
Install
an
Echo Board (Front)
(with
dual controls on the front in the Talkback location.
Talkback control is cut free of the dimmer board and moved
to the side.)
$80
or $90
Install a
Record/Playback Module 120 seconds
(wired inside the radio with
a switch on the side to record 120 seconds and to play it back)
$77
Install
a
Noise toy
(wired inside the radio with
a switch or pushbutton to trigger any 30 second sound byte
you want)
$65
Install
a
Noise toy as a background theme music
(wired inside the radio with
a switch to play any background music at very low volume so
you can talk over it.)
Download Manual
button to change to the next video)
